A BEGINNER'S GUIDE TO PLUMBING FOR BATHTUB INSTALLATION

A Beginner's Guide to Plumbing for Bathtub Installation

A Beginner's Guide to Plumbing for Bathtub Installation

Blog Article

Book Service

We've unearthed this great article relating to Installing A Bathtub below on the web and accepted it made good sense to write about it with you over here.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and also often, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as embeded in the new one. Make certain you have actually certified yourself for the work and also are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your washroom if you have actually already acquired a new bathtub and also don't need to transform the setup of your previous water pipes.
Your devices and also product checklist ought to consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
    Before going on to fit the new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a connection to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The former type should be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Setting up the Bath tub


    Using both wooden boards under its feet, place the tub in the called for placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
    The next goal is to ensure that the bath tub is leveled all round. This can be attained by checking the level and changing the feet on the tub until the spirit level reads degree.
    To mount faucets, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
    Turn on the water supply and check all joints and new pipework for leakages and also tighten them if needed. Load the tub as well as additionally check the overflow electrical outlet as well as the typical outlet for leaks.
    Finally, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the tub must wait up until the bath tub has been used at the very least once as this will resolve it right into its last setting.

    Planning for the Installment


    Firstly, the supporting frame supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
    Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its final setting.

    Tiling Around the Tub


    In the area where the bath meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface in between the bath and the tiling, causing complications with wetness and possible leaks to the ceiling below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes and also cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can crack fairly early if you do not think about this activity prior to sealing.
    Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water resistant glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I'm certainly very taken with Tools You Need to Install a New Bathtub and I am assuming you enjoyed our post. Sharing is good. One never knows, you may very well be doing someone a favor. We treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Free Estimates

    Report this page